resume2009

Seeking a position that will offer growth using of my well-developed technical and academic skills.

ep 2002 until now: working as a petroleum engineer in POGC (Pars Oil & Gas Company). My work experience included:



• Involved in Drilling and Completion Operation In southpars field on SAGA1&2 Japanese Drilling rigs, involved in Monobore Cemented completion project which is applied for the first time in Middle East.

• Surface, process and Subsurface Production engineering (revamping and modifying plan to increase capacity of offshore plant ΈAssalouye)

• Involved in PSP (PLT: production logging tools by SLB CO.) project in phases 2&3 offshore.

• Well performance analysis: Driving IPR&WHPC curves & Nodal Analysis, DHFP (Down Hole Flowing Pressure) calculations, Applying HYSYS software to simulate well head test separator and well production allocation based on well flowing pressures.
• Member of start up team on south pars phase one wellhead platforms, planning & performing well test campaign in well head test separator for all wells to optimize well productions.

• Produced Water sources analysis for gas-condensate wells in south pars gas.

• Supervision on pressure-temperature survey for wells of phases 1&2&3 (14 wells) in south pars gas-condensate field that done by ALMANSOORY CO.

• Site supervisor during the perforation (CCL, and correlation), clean-up and well test with SCHLUMBERGER.
• Wellhead, wire line services and work over supervision.

• Involved in coiled tubing operation.
• Familiar with operating & repairing of hydraulic and manual surface and subsurface safety valves (wireline and tubing retrievable types). And modifying return oil lines for hydraulic valves to prevent wasting hydraulic oil.

• Repairing actuators of hydraulic surface safety valves(CAMERON TYPE 15000 PSI)
• Wellhead & X-mass Tree pressure integrity test.

• Familiar with different completion equipments such as: Packers, Liner hangers, SSSV, gas lift valves, submersible pumps (REDA), PSI unit (pressure-temperature units in down holes), SSD, and other usual equipments.

• Writing and preparing indent for well equipments & spare parts that will be needed in future.

• Master of Energy and Environmental Management: Eni Corporate University-Milan-ITALY - graduated in jun 2007
Final project: assessment of lean profile in well drilling technology by ENI and comparison by conventional drilling methods in terms of environmental impacts and cost analysis.


• Bachelor of Engineering in Petroleum: Petroleum University of Technology, Ahwaz, Iran-graduated in 2002 with honours.
Final Project: “calcium sulfate scaling during water injection and the effect on permeability in porous media” published in SPE by Dr. Moghadasi
Advisor: Dr. Moghadasi & Co-Advisor: Dr Jamiolahmadi

-UBD (under balance drilling) by NAFTCAVE COMPANY
-H.U.E.T (Simulated Helicopter Underwater Escape Training Course)
-STCW (Standard of Training, Certification and Watch keeping for seafarers)
-H2S safety and Medic First Aid.

un 2006 up to Jun 2007 student in master degree of energy and environment management in Eni corporate university: concerning business management in the energy and environment sector and assessment the impact of energy and environmental policies on business and management.


• Jun 2005 2 weeks training course in research centre of petroleum industry about hydrate formation& phase behavior of hydrocarbons and HYSYS Software
• December 2004 6 weeks in NISOC to be familiar with well testing, well logging, well planning

• September 2004 H.U.E.T (Simulated Helicopter Underwater Escape Training)Course in Mahmoudabad Technical and Engineering Complex
• September 2003 1 week course by NAFTCAV CO. about U.B.D(under balance drilling)
• December 2001 6 months OJT(ON JOB TRAINING) in kish island and offshore drilling rigs SAGA1&2 running liner, cement job, running completion, installing X-MASS TREE, perforation, stimulation, and clean up

•